Kext utility mountain lion
- KEXT UTILITY MOUNTAIN LION HOW TO
- KEXT UTILITY MOUNTAIN LION INSTALL
- KEXT UTILITY MOUNTAIN LION SERIAL
- KEXT UTILITY MOUNTAIN LION UPDATE
- KEXT UTILITY MOUNTAIN LION DRIVER
When installing OSX, name the OSX HDD "System" or something because when i named it OSX86 Clover did not list OSX in the boot menu. Turn on GraphicsInjector if needed etc, I have mine turned off because I have UEFI bios on GTX 660 and then enabler/injector needs to be off. You will also have to set your own CustomUUID.
KEXT UTILITY MOUNTAIN LION SERIAL
You can use my ist below, but you will have to change some stuff like BoardSerialNumber to add your own 17 digit string, usually you can use Chameleon Wizard to generate a serial and then apply a few random numbers at the end to make it 17 digits. Detailed explanation on config file can be found here: Go to Computer in finder and open the EFI partition that Clover mounted.ĭrop your kexts in \EFI\CLOVER\kexts\10.8
KEXT UTILITY MOUNTAIN LION INSTALL
Open Clover installer and click "Change Install Location" select your USB partition, most likely "Mac OS X Base System"Ĭlick "Customize", Select "Install for UEFI motherboards", "Install Clover in the ESP", "Themes" and Drivers64UEFI > "OsxAptioFixDrv-64". Just extract it to the HFS+ partition on the USB.
KEXT UTILITY MOUNTAIN LION HOW TO
Im not gonna write a new whol guide but im gonna explain shortly how to do it.įormat it as GPT, make 1 Partition Mac OS Extended (Journaled).Įxtract OSX installer to the USB the same way as described in the first post, but dont format or change partitions. With Clover you don't need to create a patched DSDT and it boots in native UEFI mode, so you can have CSM/Legacy Boot turned off.ĭifferences between Chameleon and Clover boot:Ĭhameleon: UEFI Motherboard > Motherboard is emulating traditional BIOS > Chameleon is emulating EFI and boots OSXĬlover: UEFI Motherboard > Clover loads and boots OSXĬlover patches the DSDT on the fly and you can create dsdt fix mask and DSDT patches will be added on the fly too.
KEXT UTILITY MOUNTAIN LION UPDATE
Reboot and if you see your bootloader, select your install drive and update your system to 10.8.5 (if system was built with an older version) and reboot ( *Note* see Troubleshooting section below if your bootloader doesn't load and you have to boot into the drive via UniBeast USB).Launch Disk Utility, select your installation drive and repair permissions.Do not install VoodooHDA yet!! You will most likely get a kernel panic after Installation step #13 if you do!.If you boot with verbose (-v) you will get stuck at “ IOAPIC: Version 0x20 Vectors 64:87”: Pic This kext is needed or your system wont boot and will get stuck at the Grey Apple boot screen with no spinning dial. The version contained in MultiBeast 5.0.2 is v1.5 which may also work yet I have not tried since I know v.1.3.6 works. Install AppleACPIPlatform kext I provided and rebuild cache ( *Note* AppleACPIPlatform.kext is v1.3.6.Launch Champlist, click Kext Utility and also select the drive you installed OS X on in upper right corner.Select userDSDT ( *Note* be sure to read what this installs) and install : Pic.
KEXT UTILITY MOUNTAIN LION DRIVER
Lacie USB 3.0 Driver (version 1.0.10) **This is not needed if installing the USB3 kext from MultiBeast 5.3.1**.Follow this Guide for Creating Your Own DSDT) DSDT.aml file ( *Note* I created and patched my own DSDT for BIOS version 1602.The native Kext Utility is also available in the Application>Utilities folder for rebuilding cache so use whichever you prefer) You can also edit your & smbios plist settings with it instead of using MultiBeast. MultiBeast 5.0.2 or newer, KextBeast or Champlist ( *Note* I prefer and used Champlist for bootloader updates, cache rebuild, and kext install.Highlight the drive you just installed OS X onto and select it without typing any parameters.Reboot after the installation is completed and again boot into the USB drive created with UniBeast.Install OS X 10.8 onto the newly partitioned drive.Partition as “Mac OS Extended (Journaled)" with a GUID Partition Map Table.Select the drive you want to install OS X 10.8.*Note* This was needed to prevent a black screen after I selected the UniBeast USB drive to begin the installation.You can download latest MultiBeast from tonymacx86 downloads. *Note*Everything else you will need, with the exception of MultiBeast and KextBeast, are attached to this post as compressed files.so just download and unzip.If you create a brand new one following the tutorial, the App Store download will be 10.8.5 which is the most recent version out at the time this guide was created. *Note*My UniBeast USB was created with the App Store download of 10.8.A bootable USB Mountain Lion installer created with UniBeast - Follow this tutorial: Link.Processor: Intel Core i7-870 "Lynnfield" (LGA1156)īefore Installing Please have the following created:.Building a CustoMac Hackintosh: Buyer's Guide